Climate Change Sustainability Water Efficiency / Dry Drains Water Quality Gray Water / Black Water Codes, Standards & Regulation Product Labeling counterfeit Product Disease Outbreak Control Water Harvesting
12
New valve islolates water flow Author: Jonathan Jackson 4 September 2009
Tags: Valves, Water efficiency, Innovation, Products, Australasia Page 1 of 2 | Single page
Thirty years as a craftsman plumber led Andrew Southen to design an isolation valve, the Isovalve, that replaces a temporary test plug, includes a water filter and allows water flow to be adjusted at individual installations.

Isotec Limited has secured patents in New Zealand, Australia, Europe, the UK and USA as well as a number of other countries. The company has just received Watermark certification in Australia for the Isovalve and has signed a Distribution agreement with Abey Australia. Their product is an isolating valve which enables plumbers to connect plumbing fixtures and appliances without having to turn the water off at ‘distant’ isolating shut off valves.

“The idea for the Isovalve came about when I was at a job where all I had to do was fit a basin at a medical laboratory,” Isovalve creator Andrew Southen says.

The basin at Christchurch Radiation Laboratory was a messy job that involved turning off the entire building’s water supply.

“The test plugs had already been installed and were sticking out of the wall ready for me to remove and then connect the flexible connections from the basin faucet. It should have been easy, but being a plumber of many years I knew that turning off the water in this place was not going to be straightforward. I said to myself, I wish these test plugs were valves. If I didn’t have to turn the water off, this job would only take half an hour.”

After several calls to locate the relevant authorities and experts, Andrew found himself having to go to two remote locations to turn off both the hot and cold water. However, the first hot water tap wouldn’t turn off which resulted in Andrew having to climb a ladder into the ceiling.

With the water finally turned off and mostly drained from the pipe system, Andrew removed the test plugs.

“The bucket soon filled up and before long I had water all over the floor and still flowing. This is the time when you hope you don’t have a problem as water is an essential ingredient in the operation of this building. Finally I had the tap installed but I had to crawl back up into the ceiling, turn the hot water back on, run out to the road and turn the cold water back on, then run back to make sure I didn’t have a leak.”

All in all the job took three hours and left Andrew stressed and tired. A valve would have meant the job took 40 minutes and the client wouldn’t have had to face the ordeal of having their water turned off.

So Andrew set out to design a valve that requires no off-site mains water shut-off and saves customers time, money, water and energy.

Since the idea formed in 2006, the invention first made from a crude piece of brass, has been redeveloped and continuously improved on site to the point where it can now be taken to the international market.

Installed in place of, and at the same time a traditional test plug would normally be installed, the Isovalve enables the wall board, tiles or joinery to be neatly drilled and installed over the Isovalve. Once the wall lining is completed it’s a simple matter of removing the protective cardboard sleeve from the Isovalve, sliding on the wall flange and attaching the fixture to the Isovalve outlet. The water is then turned on to the fixture at the Isovalve.

The Isovalve is manufactured from DZR chrome-finished solid brass rod, with only two components to the unit: the Valve Body and the Isonipple. It comes with a twin O-ring to the valve spindle and acetyl washer. It is controlled by turning the front dome, however a 4mm Allen key is also supplied with every Isovalve. It is suitable for all water pressures and will be supplied to the Australian market with a chrome finished cover plate. Each comes with its own in-line filter ensuring compliance with tapware warranties. There are presently four models of Isovalve available, including one dual outlet model.

The cost of installation depends on the number of fittings required but generally the Isovalve itself costs no more than a standard angle valve. The Isovalve will usually replace the test plug, brassbarrel nipple and sometimes an angle valve or a chrome or brass elbow.

Continued...



12